Screws by Drive

Type 316 Stainless Steel for Superior Corrosion Resistance Sharx Marine Screws are made of salt water safe type 316 Stainless Steel. Use in composite materials, fiberglass, engineered wood products such as plywood, OSB, laminated wood veneers and wood substitutes High-low thread form with "teeth" bites fast and holds tight Strength compares favorably with that of carbon steel fasteners Screws up to 1" in length are fully threaded; screws more than 1" long are threaded 2/3 of the shank length #2 Phillips drive; Extra sharp point Also available in pan head

Read more less

Star Drive - Type 316 Stainless Steel Experience the revolutionary 4 corner thread with raised ridge point for fast penetration, reduced drive torque and outstanding holding power. Self Countersinking Flat Head with Nibs Install using 35% less torque! For Decking, Docks and Boardwalks; Finishing, Millwork & Trim Star Drive 6 Lobe Type 316 Stainless Steel for the ultimate in corrosion resistance Approved for use in ACQ treated lumber

Read more less

6 Lobe Star drive recess, similar to Torx® Self-countersinking bugle head in medium & soft density wood Type 17 notched point for fast penetration Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold Approved for use in all pressure treated lumber Always specify Type 316 Stainless Steel for Salt Water applications New package sizes, same screws Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the star recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent the screw head from twisting off.

Read more less

For Attaching Fiber Cement Siding through Furring Strips to Wood Studs Fasten fiber cement to wood studs and Stress-Skin panels .390" diameter wafer head with countersinking nibs #2 square drive - threaded full length Type 17 point with coarse threads Type 316 Stainless Steel for the ultimate in corrosion resistance Use 1-1/4" screws to attach fiber cement siding to Stress-Skin panels Use 1-5/8" & 2-1/4" screws to blind fasten fiber cement lap siding to wood studs AISI Grade 316 Stainless Steel has lower carbon content than 305 or 302HQ and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application.

Read more less

Type 305 Stainless Steel - Wood Screws Type 17 notched point for fast penetration Self-countersinking bugle head Square drive recess reduces driver cam-out Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold           Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the square recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the square drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent twisting off the screw head.

Read more less

305 & 316 Star Drive Type 17 point for fast penetration Self-countersinking trim head Dry lubricated with non-stick film Threaded approximately 2/3 of shank Available in AISI type 305 and 316 stainless steel

Read more less

For Attaching Wood Siding, Wood Panels and Metal Trim to Steel Studs Screws have a trim head, #3 drill point and T-15 star drive. Triple strength corrosion resistance: 410 stainless steel + Xylan coating + Bright hardening Also perfect for use with stainless steel, aluminum and steel deck framing systems Drill point with auger tip for self tapping

Read more less

This screw fastens all materials to wood or wood substitute materials. #2 Square Drive Type 17 point Course Thread

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish.

Read more less

Type 305 Stainless Steel - Star Drive For fast and easy installation in high-exposure environments. DWP screws are built to last. Revolutionary 4 corner thread with raised ridge point for fast penetration and outstanding holding power Self Countersinking Flat Head with Nibs Installs with 35% less torque! For Decking, Docks and Boardwalks; Finishing, Millwork & Trim Star Drive 6 Lobe Type 305 Stainless Steel Approved for use in ACQ treated lumber

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

316 Stainless Steel - Wood Screws Salt Water Safe Type 17 notched point for fast penetration Self-countersinking bugle head Square drive recess reduces driver cam-out Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold Use with cedar, redwood, engineered wood and preservative treated *Type 316 Stainless Steel should always be specified for salt water applications. 316 grade stainless steel has a lower carbon content than 18-8 type stainless (302HQ, 304 and 305) and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application to prevent rusting & bleeding through. Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the square recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the square drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent twisting off the screw head.

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

For Composite & Capstock Decking CAP-TOR xd is designed for use with Trex, Timber-Tech, Fiberon, Azek and other composites & capstocks Type 305 Stainless Steel for superior corrosion resistance Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 15 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform finish install using the Smart-Bit Depth Setter

Read more less

For Composite & Capstock Decking CAP-TOR xd is designed for use with Trex, Timber-Tech, Fiberon, Azek and other composites & capstocks Type 305 Stainless Steel for superior corrosion resistance Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 15 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform finish install using the Smart-Bit Depth Setter

Read more less

For Composite & Capstock Decking CAP-TOR xd is designed for use with Trex, Timber-Tech, Fiberon, Azek and other composites & capstocks Type 305 Stainless Steel for superior corrosion resistance Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 15 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform finish install using the Smart-Bit Depth Setter

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish. Not sure what color you need? Use the interactive Deck Matcher

Read more less

Square Drive #1 Square Drive - small unobtrusive .230" head Type 17 point for fast penetration Self-countersinking trim head Square drive recess reduces driver cam-out problems Dry lubricated with non-stick film Our stainless steel trim head screws are threaded approximately 2/3 of shank Available in AISI type 305 and 316 stainless steel AISI Grade 316 Stainless Steel has a lower carbon content than 305 or 302HQ and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application.

Read more less

305 Stainless Steel Type 17 point #2 Phillips Drive Wire-lath truss screw for fastening lath to wood

Read more less

Hardened 410 Stainless Steel #2 drill point Phillips drive Low Profile flat truss head Xylan coating provides additional corrosion resistance

Read more less

Star Drive - Type 316 Stainless Steel Trim Head T15 star drive - 6 lobe 4 corner thread with raised ridge point Fast penetration & superior holding power Installs using 35% less torque! Type 316 stainless steel for the ultimate in corrosion resistance Salt Water Safe Approved for use in treated lumber

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread*, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. #10 x 3-1/8" screws are Case Hardened Carbon Steel, the rest are 316 Stainless Steel *Reamer Thread is only present on screws 2" and longer

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. Screws are also available in Case Hardened Carbon Steel and  316 Stainless Steel

Read more less

For Composite & Capstock Decking Type 316 Stainless Steel for the Ultimate in corrosion resistance Salt Water Safe Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 10 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform look, install using the Smart-Bit Depth Setter

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish.

Read more less

For Attaching Fiber Cement Siding through Furring Strips to Steel Studs Hardened 410 Stainless Steel .390" diameter ribbed wafer head with self-countersinking nibs #3 drill point - tapping screw thread #2 square drive #8 x 1-5/8" threaded to within 5/16" of top of head #8 x 2-1/4" threaded approximately 2/3 of shank

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread*, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. Screws are Case Hardened Carbon Steel, also available in 316SS *Reamer Thread is only present on screws 2" and longer

Read more less

For Composite & Capstock Decking Type 316 Stainless Steel for the Ultimate in corrosion resistance Salt Water Safe Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 10 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform look, install using the Smart-Bit Depth Setter

Read more less

For Composite & Capstock Decking Type 316 Stainless Steel for the Ultimate in corrosion resistance Salt Water Safe Extra deep T-20 star recess to minimize "wobble" at screw starting Undercut head design - a specially engineered head that cleanly penetrates the hard outer coating of capstock products Transverse™ Threading eliminates "mushroom" effect common to composite decking installed using standard deck screws. Auger Point for faster, easier entry. Helps prevent splitting Available in 10 colors to blend with a wide range of composite deck board colors Use the Deck Matcher to find the best color. For a uniform look, install using the Smart-Bit Depth Setter

Read more less

Stainless Steel Screws with Color Coated Heads For Hardwood, Cedar, Redwood and Pressure Treated Decking Headcote screws are designed to work with Smart-Bit® Predrilling and Countersinking Tools, for a perfect finish.

Read more less

Trim Head, T15 star drive Box thread reduces required driving torque by 35% Perfect for decks, finishing, millwork and trim Sharp point specially designed to easily penetrate hardwoods

Read more less

The Fine Screw™ is U2's trim screw design This screw has a specially designed star drive that holds U2 bits so tightly that the screws can be installed one-handed.

Read more less