Hand Drive Screws

Star Drive - Type 316 Stainless Steel Experience the revolutionary 4 corner thread with raised ridge point for fast penetration, reduced drive torque and outstanding holding power. Self Countersinking Flat Head with Nibs Install using 35% less torque! For Decking, Docks and Boardwalks; Finishing, Millwork & Trim Star Drive 6 Lobe Type 316 Stainless Steel for the ultimate in corrosion resistance Approved for use in ACQ treated lumber

Read more less

Type 316 Stainless Steel for Superior Corrosion Resistance Sharx Marine Screws are made of salt water safe type 316 Stainless Steel. Use in composite materials, fiberglass, engineered wood products such as plywood, OSB, laminated wood veneers and wood substitutes High-low thread form with "teeth" bites fast and holds tight Strength compares favorably with that of carbon steel fasteners Screws up to 1" in length are fully threaded; screws more than 1" long are threaded 2/3 of the shank length #2 Phillips drive; Extra sharp point Also available in pan head

Read more less

The Construction screw does the job of a lag screw. Dome Head enhances the structural capability. Tapper Point which consists of the Cork Screw Start and Blade Cutting Thread for easy piercing and alleviating strain on the material. Specially designed Tight Star Recess system holds U2 bits firmly in place allowing these screws to be installed with one hand. "Talon Grip" nibs under the head hold the screw tight to prevent loosening and dig into the material when countersunk. Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. ***This thread is not on the 1/4" x 2" screw

Read more less

6 Lobe Star drive recess, similar to Torx® Self-countersinking bugle head in medium & soft density wood Type 17 notched point for fast penetration Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold Approved for use in all pressure treated lumber Always specify Type 316 Stainless Steel for Salt Water applications New package sizes, same screws Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the star recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent the screw head from twisting off.

Read more less

The Strong-Drive SD Connector screw is designed for use in stainless steel connectors, replacing the need for nails. Load Rated Tested and approved for use with many Simpson Hangers and Connectors In certain applications, the load values achieved by the #9 SD Screw is greater than that of 10d common nails Specially designed screw shank pairs with holes in Simpson Connector Box includes the hex driver

Read more less

For Attaching Fiber Cement Siding through Furring Strips to Wood Studs Fasten fiber cement to wood studs and Stress-Skin panels .390" diameter wafer head with countersinking nibs #2 square drive - threaded full length Type 17 point with coarse threads Type 316 Stainless Steel for the ultimate in corrosion resistance Use 1-1/4" screws to attach fiber cement siding to Stress-Skin panels Use 1-5/8" & 2-1/4" screws to blind fasten fiber cement lap siding to wood studs AISI Grade 316 Stainless Steel has lower carbon content than 305 or 302HQ and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application.

Read more less

Type 305 Stainless Steel - Wood Screws Type 17 notched point for fast penetration Self-countersinking bugle head Square drive recess reduces driver cam-out Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold           Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the square recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the square drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent twisting off the screw head.

Read more less

305 & 316 Star Drive Type 17 point for fast penetration Self-countersinking trim head Dry lubricated with non-stick film Threaded approximately 2/3 of shank Available in AISI type 305 and 316 stainless steel

Read more less

This screw fastens all materials to wood or wood substitute materials. #2 Square Drive Type 17 point Course Thread

Read more less

Type 305 Stainless Steel - Star Drive For fast and easy installation in high-exposure environments. DWP screws are built to last. Revolutionary 4 corner thread with raised ridge point for fast penetration and outstanding holding power Self Countersinking Flat Head with Nibs Installs with 35% less torque! For Decking, Docks and Boardwalks; Finishing, Millwork & Trim Star Drive 6 Lobe Type 305 Stainless Steel Approved for use in ACQ treated lumber

Read more less

316 Stainless Steel - Wood Screws Salt Water Safe Type 17 notched point for fast penetration Self-countersinking bugle head Square drive recess reduces driver cam-out Threaded approximately 2/3 of shank on most sizes Deep coarse threads for better hold Use with cedar, redwood, engineered wood and preservative treated *Type 316 Stainless Steel should always be specified for salt water applications. 316 grade stainless steel has a lower carbon content than 18-8 type stainless (302HQ, 304 and 305) and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application to prevent rusting & bleeding through. Important Installation Instructions: If the screws are to be driven by a screw gun, be sure the bit is securely seated in the square recess of the screw. Start slowly and gradually increase speed until the head is driven flush. A high driving speed increases the chance of stripping the square drive recess. If the tool has an adjustable torque collar, use a piece of scrap lumber to determine the proper setting needed to drive the head flush with the surface. This will prevent twisting off the screw head.

Read more less

Type 316 Stainless Steel for ultimate corrosion resistance 1/4” diameter high-strength structural wood screw 3/8” hex head with 0.48” integrated washer Type-17 point enables easy driving with no pre-drilling and minimal wood splitting Used to fasten certain heavy duty framing connectors to wood members Excellent for fastening ledger boards 25pc box

Read more less

The Construction screw does the job of a lag screw.  This code-compliant heavy-duty self-tapping structural fastener is versatile and great for a variety of uses. Dome Head provides an extra-large bearing surface under the head. Tapper Point enables easy piercing and relives strain on material while installing. Tight Star Recess system is specially designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Talon Grip nibs secure screw fastening to prevent loosening over time.  Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. The perfect fastener for staircases, deck frames, ledger boards, joists, rafters, planters, play sets and more. 

Read more less

Hardened 410 Stainless Steel #2 drill point Phillips drive Low Profile flat truss head Xylan coating provides additional corrosion resistance

Read more less

305 Stainless Steel Type 17 point #2 Phillips Drive Wire-lath truss screw for fastening lath to wood

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread*, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. #10 x 3-1/8" screws are Case Hardened Carbon Steel, the rest are 316 Stainless Steel *Reamer Thread is only present on screws 2" and longer

Read more less

Perfect for trim board, railings and fine carpentry Small Finishing head, 0.196" T-10 Star Drive Double twist at the head provides drawing strength> Tapper Point allows for the screw to easily pierce the material and alleviate strain. 316 Stainless Steel, marine-grade for ultimate corrosion resistance.

Read more less

Star Drive - Type 316 Stainless Steel Trim Head T15 star drive - 6 lobe 4 corner thread with raised ridge point Fast penetration & superior holding power Installs using 35% less torque! Type 316 stainless steel for the ultimate in corrosion resistance Salt Water Safe Approved for use in treated lumber

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. Screws are also available in Case Hardened Carbon Steel and  316 Stainless Steel

Read more less

For Attaching Fiber Cement Siding through Furring Strips to Steel Studs Hardened 410 Stainless Steel .390" diameter ribbed wafer head with self-countersinking nibs #3 drill point - tapping screw thread #2 square drive #8 x 1-5/8" threaded to within 5/16" of top of head #8 x 2-1/4" threaded approximately 2/3 of shank

Read more less

U2's Cap Screw is designed for interior and exterior use. Modified low profile truss head with star drive Perfect for cabinets, trim, moulding, light duty framing, vinyl siding and window installations. Dome head features a cutting ribbon underhead The Tapper Point is designed to easily pierce while evenly dispersing any strain on the material. The tip of the screw begins with a Cork Screw start. When paired with the blade cutting thread, this screw is installed quickly and easily. As with all U2 screws, it features a tight star recess that holds the U2 bit tightly. It is such a perfect fit that this screw can be installed with one hand. This screw takes a T15 bit.

Read more less

The U2 Fasteners Black Flat Head Screw combines versatility and style.  Great for use in deck frames, fencing, ledger boards, posts, and professional timber construction. Flat Head with Talon Grip.  Allows for increased pull-through resistance. Tapper Point enables easy piercing and reduced strain on material while installing. Tight Star Recess system is designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Screw coating is CR3 free base finished with a black nano coating.  It protects against corrosion, wear, and friction ensuring long lasting protection 

Read more less

The Universal Screw™ is great for use in deck construction. Tapper Point, consisting of the Cork Screw Start and Blade Cutting Thread allows the screw to pierce materials easily. Screws feature a Star Recess system that holds the U2 bits securely in place. This allows the screw to be installed one-handed. The universal screw includes nibs that help the screw to countersink into the toughest of materials. Below the smooth shank is the Reamer Thread*, which enlarges the hole to create a passage when drawing materials together and reduces tension for the screw head. Screws are Case Hardened Carbon Steel, also available in 316SS *Reamer Thread is only present on screws 2" and longer

Read more less

The Construction screw does the job of a lag screw.  This code-compliant heavy-duty self-tapping structural fastener is versatile and great for a variety of uses. Dome Head provides an extra-large bearing surface under the head. Tapper Point enables easy piercing and relives strain on material while installing. Tight Star Recess system is specially designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Talon Grip nibs secure screw fastening to prevent loosening over time.  Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. The perfect fastener for staircases, deck frames, ledger boards, joists, rafters, planters, play sets and more. 

Read more less

The Fine Screw™ is U2's trim screw design This screw has a specially designed star drive that holds U2 bits so tightly that the screws can be installed one-handed.

Read more less

Trim Head, T15 star drive Box thread reduces required driving torque by 35% Perfect for decks, finishing, millwork and trim Sharp point specially designed to easily penetrate hardwoods

Read more less